NetTCPIP.dll
Associated Error Codes
Below lists error codes and symbolic names found for this module.
| Code | Found in | Description |
|---|---|---|
| 0x1 | 1011 | Can not find the required property %1 |
| 0x2 | 1011 | Not all required properties are specified: %1 and either one of %2 %3 |
| 0x3 | 1011 | Not all required properties are specified: either one of %1 %2 and either one of %3 %4 |
| 0x4 | 1011 | Not all required properties are specified: %1 %2 and either one of %3 %4 |
| 0x5 | 1011 | Not all required properties are specified: %1 and either %2 %3 %4 %5 or %6 %7 |
| 0x6 | 1011 | Only the custom templates InternetCustom and DatacenterCustom can be modified. |
| 0x7 | 1011 | %1 must be the same as %2, %3 must be the same as %4 or only one of the ranges must be wildcard (0, 65535) |
| 0x8 | 1011 | Properties that need modification should not include any of the following %1 %2 %3 %4 %5 %6 |
| 0x9 | 1011 | Properties that need modification should not include any of the following %1 %2 %3 %4 %5 %6 %7 %8 %9 %10 |
| 0xa | 1011 | Properties that need modification should not include any of the following %1 %2 %3 %4 %5 %6 %7 %8 %9 %10 %11 %12 |
| 0xb | 1011 | Instance %1 %2 not found |
| 0xc | 1011 | Instance %1 already exists |
| 0xd | 1011 | Invalid parameter %1 %2, %3 should not be specified |
| 0xe | 1011 | Invalid parameter %1 Days: %2!lu! Hours: %3!lu! Minutes: %4!lu! Seconds: %5!lu! Microseconds: %6!lu! |
| 0xf | 1011 | Invalid parameter %1 |
| 0x10 | 1011 | Invalid parameter %1 %2 |
| 0x11 | 1011 | Invalid parameter %1 %2 %3 %4 |
| 0x12 | 1011 | Invalid parameter %1 %2!lu! |
| 0x13 | 1011 | Inconsistent parameters %1 %2 and %3 %4 |
| 0x14 | 1011 | Value of property %1 should be at most the value of property %2 |
| 0x15 | 1011 | Value of property %1 should be at most %2!lu! |
| 0x16 | 1011 | Property %1 is read-only |
| 0x17 | 1011 | This feature is available on servers only. |
| 0x18 | 1011 | Properties %1 and %2 should have values at the same time |
| 0x19 | 1011 | Properties %1 and %2 should not have values at the same time |
| 0x1a | 1011 | When property %1 is %2!lu!, %3 and %4 can not be set |
| 0x1b | 1011 | Properties %1 %2 %3 %4 and %5 %6 should not have values at the same time |
| 0x1c | 1011 | Can only modify/create/delete Neighbor object whose State is Permanent |
| 0x1d | 1011 | Default loopback address cannot be deleted |
| 0x1e | 1011 | Default loopback route cannot be deleted |
| 0x1f | 1011 | IPv4 protocol is not installed. |
| 0x20 | 1011 | This feature is not available on servers. |
| 0x21 | 1011 | DefaultGateway %1 is not on the same network segment (subnet) that is defined by the IP address %2 and PrefixLength %3!lu!. |
| 0x22 | 1011 | Interface %1 does not support setting LinkLayerAddress. |
| 0x23 | 1011 | The parameter %1 must be specified. |
| 0x24 | 1011 | Both IP addresses must be from the same address family. |
| 0x25 | 1011 | Not supported. |
| 37 entries | ||