diskraid.exe

Associated Error Codes

Below lists error codes and symbolic names found for this module.

Code	Found in	Description
0x4000271b	1011	Microsoft DiskRAID version %1!d!.%2!d!.%3!d!.%4!d! Copyright (C) 2003-2013 Microsoft Corporation. On computer: %5!s!
0x4000271c	78.11011	DISKRAID>
0x4000271d	78.11011	Leaving DiskRAID...
0x40002725	78.11011	DiskRAID is using standard input mode.
0x40002726	78.11011	DiskRAID is using script mode.
0x40002727	78.11011	DiskRAID is using script file: %1!s!
0x4000272a	78.11011	The name you specified was accepted but was truncated due to provider constraints.
0x4000272b	78.11011	A reboot is REQUIRED for the LUN uninstall to fully take effect. If you initiate further operations without rebooting, the outcome and machine state are undefined.
0x400027b1	78.11011	Path ### Hbaprt ### Port ### Ctlr ### Subsys ### LUN ### Status -------- ---------- -------- -------- ---------- ------- ----------
0x400027b2	78.11011	Path %1!-3lu! Hbaprt %2!3.3s! Port %3!-3lu! Ctlr %4!-3lu! Subsys %5!-3lu! LUN %6!-3lu! %7!-10.10s!
0x400027b3	78.11011	LUN %1!-3lu! %2!-10.10s!
0x400027b5	78.11011	There are no paths to list.
0x400027b6	78.11011	Path ### Hbaprt ### Port ### Ctlr ### Status Pri Weight -------- ---------- -------- -------- ---------- --- ----------
0x400027b7	78.11011	Path %1!-3lu! Hbaprt %2!3.3s! Port %3!-3lu! Ctlr %4!-3lu! %5!-10.10s! %6!3.3s! %7!10lu!
0x400027bb	78.11011	Path ### Iadap ### Tptl ### Subsys ### LUN ### Status -------- --------- -------- ---------- ------- ----------
0x400027bc	78.11011	Path %1!-3lu! Iadap %2!-3lu! Tptl %3!-3lu! Subsys %4!-3lu! LUN %5!-3lu! %6!-10.10s!
0x400027bd	78.11011	LUN %1!-3lu! %2!-10.10s!
0x400027c0	78.11011	Path ### Iadap ### Tptl ### Status Pri Weight -------- --------- -------- ---------- --- ----------
0x400027c1	78.11011	Path %1!-3lu! Iadap %2!3.3lu! Tptl %3!-3lu! %4!-10.10s! %5!3.3s! %6!10lu!
0x400027ce	78.11011	iSCSI Name : %1!s!
0x400027cf	78.11011	Initiator iSCSI Name Local -------------------------------------------------- -----
0x400027d0	78.11011	%1!50.50s! %2!-5.5s!
0x400027d9	78.11011	Prov ### Name Version Type -------- --------------------------------------------- ---------- -------
0x400027da	78.11011	%1!s! Prov %2!-3lu! %3!-45.45s! %4!-10.10s! %5!-7.7s!
0x400027db	78.11011	There are no VDS hardware providers to list.
0x400027e3	78.11011	Provider %1!d! is now the selected provider.
0x400027e4	78.11011	There is no VDS hardware provider selected. To select a provider, specify the Prov ### for the provider you wish to select. Example: SELECT PROVIDER 0 To get a list of registered VDS hardware providers, enter LIST PROVIDERS.
0x400027ed	78.11011	Name : %1!s! Identifier : %2!s! Version String : %3!s! Version GUID : %4!s! VDS Support : %5!s!
0x4000283d	78.11011	Subsys ### Name Status Health ---------- ------------------------------ ---------- ----------
0x4000283e	78.11011	%1!s! Subsys %2!-3lu! %3!-30.30s! %4!-10.10s! %5!-12.12s!
0x4000283f	78.11011	There are no subsystems to list.
0x40002847	78.11011	Subsystem %1!d! is now the selected subsystem.
0x40002848	78.11011	There is no subsystem selected. To select a subsystem, specify the Subsys ### for the subsystem you wish to select. Example: SELECT SUBSYSTEM 0 To get a list of available subsystems, enter LIST SUBSYSTEMS.
0x40002851	78.11011	Name : %1!s! Identifier : %2!s! Status : %3!s! Health : %4!s! Enclosures : %5!s! Buses : %6!d! (%7!d! slots per bus) Drives : %8!d! Present Controllers : %9!d! Maximum, %10!d! Present Stripe Sizes : %11!s! Rebuild Priority : %12!d! Capabilities : %13!s! LUN types : %14!s! Interconnects : %15!s!
0x40002874	78.11011	iSCSI Name : %1!s! Target ### : %2!-3.3s! Subsys ### : %3!d!
0x40002875	78.11011	No import target was set for this subsystem.
0x400028a1	78.11011	Ctlr ### Name Status Health Ports LUNs -------- -------------------- ---------- ------------ ----- ----
0x400028a2	78.11011	%1!s! Ctlr %2!-3lu! %3!-20.20s! %4!-10.10s! %5!-12.12s! %6!5d! %7!4d!
0x400028a3	78.11011	There are no controllers to list.
0x400028a6	78.11011	%1!s! Ctlr %2!-3lu! %3!-20.20s! %4!-10.10s! %5!-12.12s! %6!5d!
0x400028ab	78.11011	Controller %1!d! is now the selected controller.
0x400028ac	78.11011	There is no controller selected. To select a controller, specify the Ctlr ### for the controller you wish to select. Example: SELECT CONTROLLER 0 To get a list of available controllers, enter LIST CONTROLLERS.
0x400028b5	78.11011	Name : %1!s! Identifier : %2!s! Status : %3!s! Health : %4!s!
0x400028b9	78.11011	%1!u! Port(s): Port ### Name Identifier Status -------- -------------------- -------------------- ----------
0x400028ba	78.11011	%1!1.1s! Port %2!-3lu! %3!-20.20s! %4!-20.20s! %5!-10.10s!
0x400028bd	78.11011	No ports are present on this controller.
0x400028c3	78.11011	%1!u! Associated LUN(s):
0x400028c4	78.11011	No LUNs are associated with this controller. Note: LUNs are associated with controller ports rather than with controllers starting with VDS 1.1 compliant providers.
0x400028c5	78.11011	Note: Controller port information is no longer displayed using this command starting with VDS 1.1 compliant providers. Instead use LIST PORT and DETAIL PORT to view port information.
0x400028c6	78.11011	The associated LUNs could not be retrieved for at least one of the controllers. Note: LUNs are associated with controller ports rather than with controllers starting with VDS 1.1 compliant providers.
0x40002905	78.11011	Drive ### Status Health Size Free Bus Slot Flags --------- ---------- ------------ -------- -------- --- ---- -----
0x40002906	78.11011	%1!s! Drive %2!-3lu! %3!-10.10s! %4!-12.12s! %5!5I64u! %6!-2.2s! %7!5I64u! %8!-2.2s! %9!3hd! %10!4hd! %11!-5.5s!
0x40002907	78.11011	There are no drives to list.
0x40002909	78.11011	Drive ### Status Health Size Free Bus Slot Extent --------- ---------- ------------ -------- -------- --- ---- --------
0x4000290a	78.11011	%1!s! Drive %2!-3lu! %3!-10.10s! %4!-12.12s! %5!5I64u! %6!-2.2s! %7!5I64u! %8!-2.2s! %9!3hd! %10!4hd! %11!5I64u! %12!-2.2s!
0x4000290f	78.11011	Drive %1!d! is now the selected drive.
0x40002910	78.11011	There is no drive selected. To select a drive, specify the Drive ### for the drive you wish to select. Example: SELECT DRIVE 0 To get a list of available drives, enter LIST DRIVES.
0x40002919	78.11011	Name : %1!s! Identifier : %2!s! Status : %3!s! Health : %4!s! Size : %5!I64u! %6!s! (%7!I64u! %8!s! Free) Location : Bus %9!d!, Slot %10!d! Flags : %11!s! Enclosure number : %12!s! Bus Type : %13!s! Spindle speed : %14!s!
0x4000291a	78.11011	This drive is part of %1!d! LUNs:
0x4000291b	78.11011	This drive is not part of any LUNs.
0x40002969	78.11011	LUN ### Status Health Type Size Device ------- ---------- ------------ -------- -------- ------
0x4000296a	78.11011	%1!s! LUN %2!-3lu! %3!-10.10s! %4!-12.12s! %5!-8.8s! %6!5I64u! %7!-2.2s! %8!6.6s!
0x4000296b	78.11011	There are no LUNs to list.
0x4000296d	78.11011	LUN ### Status Health Type Size Dev Extent ------- ---------- ------------ -------- -------- --- --------
0x4000296e	78.11011	%1!s! LUN %2!-3lu! %3!-10.10s! %4!-12.12s! %5!-8.8s! %6!5I64u! %7!-2.2s! %8!3.3s! %9!5I64u! %10!-2.2s!
0x40002973	78.11011	LUN %1!d! is now the selected LUN.
0x40002974	78.11011	There is no LUN selected. To select a LUN, specify the LUN ### or LUN Number for the LUN you wish to select. Examples: SELECT LUN 0 SELECT LUN NUMBER 1 To get a list of available LUNs, enter LIST LUNS.
0x4000297d	78.11011	Name : %1!s! Identifier : %2!s! Status : %3!s! Health : %4!s! Size : %5!I64u! %6!-2.2s! Type : %7!s! Rebuild Priority : %8!d! Unmasked Hosts : %9!s! Caching Policy : %10!s! Stripe Size : %11!s! Flags : %12!s!
0x4000297e	78.11011	%1!d! Contributing Drives:
0x4000297f	78.11011	No drives contribute to this LUN.
0x40002981	78.11011	%1!d! Associated Controller(s):
0x40002983	78.11011	%1!d! Associated Controller Port(s):
0x40002984	78.11011	No controller ports are associated with this LUN.
0x40002986	78.11011	Load Bal. Policy : %1!s! %2!d! Path(s):
0x40002987	78.11011	%1!d! Associated Target(s):
0x40002988	78.11011	No targets are associated with this LUN.
0x40002989	78.11011	No controllers are associated with this LUN. Note: LUNs are associated with controller ports rather than with controllers starting with VDS 1.1 compliant providers.
0x4000299b	78.11011	LUN %1!d! has the following plexes: Plex ### Status Type Attrib Drive ### Status Extent -------- ---------- -------- -------- --------- ---------- --------
0x4000299c	78.11011	Plex %1!-3lu! %2!-10.10s! %3!-8.8s! %4!-8.8s! Drive %5!-3lu! %6!-10.10s! %7!5I64u! %8!-2.2s!
0x4000299d	78.11011	Drive %1!-3lu! %2!-10.10s! %3!5I64u! %4!-2.2s!
0x4000299e	78.11011	Plex %1!-3lu! %2!-10.10s! %3!-8.8s! %4!-8.8s!
0x4000299f	78.11011	This LUN does not have any plexes.
0x400029cd	78.11011	Flag Value -------------------------------------------- -----------
0x400029ce	78.11011	FCR - Fast Crash Recovery Required %1!18.18s!
0x400029cf	78.11011	FTL - Fault Tolerant %1!18.18s!
0x400029d0	78.11011	MSR - Mostly Reads %1!18.18s!
0x400029d1	78.11011	OSR - Optimize For Sequential Reads %1!18.18s!
0x400029d2	78.11011	OSW - Optimize For Sequential Writes %1!18.18s!
0x400029d7	78.11011	RBV - Read Back Verify Enabled %1!18.18s!
0x400029d8	78.11011	RMP - Remap Enabled %1!18.18s!
0x400029d9	78.11011	WTC - Write-Through Caching Enabled %1!18.18s!
0x400029da	78.11011	YNK - Yankable %1!18.18s!
0x400029e1	78.11011	MXD - Maximum Drives %1!18lu!
0x400029e2	78.11011	MXS - Maximum Size Expected %1!15I64u! %2!2.2s!
0x400029e3	78.11011	ORA - Optimal Read Alignment %1!15lu! %2!2.2s!
0x400029e4	78.11011	ORS - Optimal Read Size %1!15lu! %2!2.2s!
0x400029eb	78.11011	OWA - Optimal Write Alignment %1!15lu! %2!2.2s!
0x400029ec	78.11011	OWS - Optimal Write Size %1!15lu! %2!2.2s!
0x400029ed	78.11011	RBP - Rebuild Priority %1!18hu!
0x400029ee	78.11011	STS - Stripe Size %1!15lu! %2!2.2s!
0x40002a31	78.11011	Hbaprt ### Status Type ---------- ---------- --------------
0x40002a32	78.11011	%1!s! Hbaprt %2!-3lu! %3!-10.10s! %4!-14.14s!
0x40002a33	78.11011	There are no HBA ports to list.
0x40002a3b	78.11011	HBA Port %1!d! is now the selected HBA port.
0x40002a3c	78.11011	There is no HBA port selected. To select an HBA port, specify the Hbaprt ### for the HBA port you wish to select. Example: SELECT HBAPORT 0 To get a list of available HBA ports, enter LIST HBAPORTS.
0x40002a45	78.11011	Port WWN : %1!s! Node WWN : %2!s! Port Speed : %3!s! Supp. Port Speed : %4!s!
0x40002a4e	78.11011	%1!d! Path(s):
0x40002a95	78.11011	Port ### Ctlr ### Identifier Status LUNs -------- -------- -------------------- ---------- ----
0x40002a96	78.11011	%1!1.1s! Port %2!-3lu! Ctlr %3!-3lu! %4!-20.20s! %5!-10.10s! %6!4d!
0x40002a97	78.11011	There are no controller ports to list.
0x40002a9f	78.11011	Controller port %1!d! is now the selected controller port.
0x40002aa0	78.11011	There is no controller port selected. To select a controller port, specify the Port ### for the controller port you wish to select. Example: SELECT PORT 0 To get a list of available controller ports, enter LIST PORTS.
0x40002aa9	78.11011	Name : %1!s!
0x40002ab2	78.11011	%1!d! Path(s):
0x40002ab7	78.11011	%1!u! Associated LUN(s):
0x40002ab8	78.11011	No LUNs are associated with this controller port.
0x40002af9	78.11011	DiskRAID recognizes the following commands:
0x40002afa	78.11011	For detailed help on a command, please enter the command with the /? option. EXAMPLE: LIST /?
0x40002afb	78.11011	%1!-15.15s! - Adds an existing LUN as a plex to the selected LUN or adds a target portal to the selected target portal group.
0x40002afd	78.11011	%1!-15.15s! - Sets the list of controllers, ports, or targets active for the selected LUN.
0x40002aff	78.11011	%1!-15.15s! - Displays or changes flags for automagic LUN creation.
0x40002b01	78.11011	%1!-15.15s! - Breaks a plex from the selected LUN.
0x40002b03	78.11011	%1!-15.15s! - Creates a new LUN, target, or target portal group.
0x40002b05	78.11011	%1!-15.15s! - Deletes the selected LUN, target, or target portal group.
0x40002b07	78.11011	%1!-15.15s! - Displays detailed information of the selected object.
0x40002b09	78.11011	%1!-15.15s! - Sets the list of controllers, ports, or targets inactive for the selected LUN.
0x40002b0d	78.11011	%1!-15.15s! - Exits DiskRAID.
0x40002b0f	78.11011	%1!-15.15s! - Extends the selected LUN.
0x40002b11	78.11011	%1!-15.15s! - Flushes the cache for the selected controller.
0x40002b13	78.11011	%1!-15.15s! - Displays a list of DiskRAID commands.
0x40002b17	78.11011	%1!-15.15s! - Invalidates the cache for the selected controller.
0x40002b19	78.11011	%1!-15.15s! - Displays a list of objects of the specified type.
0x40002b1b	78.11011	%1!-15.15s! - Performs maintenance operations on specified object.
0x40002b23	78.11011	%1!-15.15s! - Sets the selected object status to offline.
0x40002b25	78.11011	%1!-15.15s! - Sets the selected object status to online.
0x40002b27	78.11011	%1!-15.15s! - Forces re-synchronization and hot-sparing to repair a LUN.
0x40002b2b	78.11011	%1!-15.15s! - Re-enumerates objects of the specified type.
0x40002b2d	78.11011	%1!-15.15s! - Refreshes internal provider data.
0x40002b2f	78.11011	%1!-15.15s! - Does nothing. Used to comment scripts.
0x40002b31	78.11011	%1!-15.15s! - Replaces the specified drive with the selected drive.
0x40002b35	78.11011	%1!-15.15s! - Resets the selected object of the specified type.
0x40002b37	78.11011	%1!-15.15s! - Selects the specified object to have focus.
0x40002b39	78.11011	%1!-15.15s! - Sets the specified flags for the selected object.
0x40002b3a	78.11011	%1!-15.15s! - Reduces the size of the selected LUN.
0x40002b3b	78.11011	%1!-15.15s! - Makes the selected LUN accessible from the specified host(s).
0x40002b3d	78.11011	%1!-15.15s! - Sets the CHAP secrets for the selected object.
0x40002b3f	78.11011	%1!-15.15s! - Displays or sets the current VSS import target for the selected subsystem.
0x40002b41	78.11011	%1!-15.15s! - Displays detailed information about the local iSCSI initiator.
0x40002b43	78.11011	%1!-15.15s! - Displays or sets the IPSEC policy for the selected object.
0x40002b45	78.11011	%1!-15.15s! - Sets the specified load balance policy to the selected object.
0x40002b47	78.11011	%1!-15.15s! - Logs the specified initiator adapter into the selected target.
0x40002b49	78.11011	%1!-15.15s! - Logs the specified initiator adapter out of the selected target.
0x40002b4b	78.11011	%1!-15.15s! - Sets the specified name to the selected object.
0x40002b4d	78.11011	%1!-15.15s! - Removes a target portal from the selected target portal group.
0x40002b4f	78.11011	%1!-15.15s! - Sets the selected object status to standby.
0x40002ee3	78.11011	Usage: ADD PLEX LUN= [NOERR] ADD TPGROUP TPORTAL= [NOERR] Adds an existing LUN as a plex to the currently selected LUN or adds an existing target portal to the currently selected target portal group. PLEX Specifies that a plex will be added to the currently selected LUN. LUN= Specifies the index of the LUN to add as a plex to the currently selected LUN. Note that all data on the LUN being added as a plex will be lost. TPGROUP Specifies that a target portal will be added to the currently selected target portal group. TPORTAL= Specifies the index of the target portal to add to the currently selected target portal group. NOERR Specifies that any failures while performing this operation should be ignored. This maybe useful in script mode. A LUN or target portal group must be selected for this operation to succeed. Example: ADD PLEX LUN=2 ADD TPGROUP TPORTAL=0
0x40002ee5	78.11011	Usage: ASSOCIATE CONTROLLERS [ADD] [,[,...]] ASSOCIATE PORTS [ADD] -[,-[,...]] ASSOCIATE TARGETS [ADD] [,[,...]] Adds or replaces the list of controllers, ports, or targets that are associated with (active for) the currently selected LUN. CONTROLLERS Specifies that a list of controllers will be associated. This is deprecated in VDS 1.1 compliant providers. PORTS Specifies that a list of ports will be associated. The ports are specified with their parent controller followed by a dash and the port . TARGETS Specifies that a list of targets will be associated. ADD Specifies that the specified objects must be added to the existing list of objects associated with the LUN. If this parameter is not specified, the list of specified objects replaces the existing list of objects associated with the LUN. A LUN must be selected for this operation to succeed. Examples: ASSOCIATE CONTROLLERS ADD 1 ASSOCIATE PORTS 0-0,0-1 ASSOCIATE TARGETS 3,6
0x40002ee7	78.11011	Usage: AUTOMAGIC AUTOMAGIC SET = [= [...]] AUTOMAGIC CLEAR {ALL \| [ [...]]} AUTOMAGIC APPLY Displays or changes the AUTOMAGIC flags that are currently in effect. Flags are identified by three-letter acronyms. To view the current values for the flags, enter AUTOMAGIC without any parameters. SET Sets the specified flags to the specified values . CLEAR Clears the specified flags . ALL Clears all automagic flags. APPLY Applies the currently set flags to the selected LUN. A LUN must be selected for this operation to succeed. Examples: AUTOMAGIC SET FCR=TRUE OSR=TRUE ORS=4MB MXD=4 FTL=TRUE AUTOMAGIC CLEAR FCR OSR
0x40002ee9	78.11011	Usage: BREAK PLEX= [NOERR] Removes the plex from the currently selected LUN. PLEX= Specifies the index of the plex to remove. This plex will not be retained, and the drive extents used by this plex will be reclaimed. NOERR For scripting only. When an error is encountered, DiskRAID continues to process commands as if the error did not occur. Without the NOERR parameter, an error causes DiskRAID to exit with an error code. A mirrored LUN must be selected for this operation to succeed. Example: BREAK PLEX=1
0x40002eeb	78.11011	Usage: CREATE LUN {SIZE= [DRIVES=[,[,...]]] \| DRIVES=[,[,...]] \| SIZE= [POOL=] \| POOL=} [STRIPESIZE=] [NOERR] CREATE TARGET NAME= [ISCSINAME=] [NOERR] CREATE TPGROUP [NOERR] Creates a new LUN, target, or target portal group. Enter: CREATE LUN /? for specific help on creating a LUN. CREATE TARGET /? for specific help on creating a target. CREATE TPGROUP /? for specific help on creating a target portal group. A subsystem must be selected for this operation to succeed.
0x40002eed	78.11011	Usage: DELETE LUN [UNINSTALL] [NOERR] DELETE TARGET [NOERR] DELETE TPGROUP [NOERR] Deletes the currently selected LUN, target, or target portal group. LUN Specifies that a LUN will be deleted. UNINSTALL Specifies that the disk on the local system associated with the LUN will be cleaned up before the LUN is deleted. TARGET Specifies that a target will be deleted. TPGROUP Specifies that a target portal group will be deleted. NOERR For scripting only. When an error is encountered, DiskRAID continues to process commands as if the error did not occur. Without the NOERR parameter, an error causes DiskRAID to exit with an error code. A LUN, target, or target portal group must be selected for this operation to succeed. Example: DELETE LUN UNINSTALL DELETE TARGET
0x40002eef	78.11011	Usage: DETAIL
0x40002ef1	78.11011	Usage: DISSOCIATE CONTROLLERS [,[,...]] DISSOCIATE PORTS -[,-[,...]] DISSOCIATE TARGETS [,[,...]] Specifies the specified controllers, ports, or targets to dissociate from (set inactive for) the currently selected LUN. CONTROLLERS Specifies that a list of controllers will be dissociated. This is deprecated in VDS 1.1 compliant providers. PORTS Specifies that a list of ports will be dissociated. The ports are specified with their parent controller followed by a dash and the port . TARGETS Specifies that a list of targets will be dissociated. A LUN must be selected for this operation to succeed. Examples: DISSOCIATE CONTROLLERS 1,2 DISSOCIATE PORTS 1-1 DISSOCIATE TARGETS 5
0x40002ef5	78.11011	Usage: EXIT Exits from DiskRAID. Example: EXIT
0x40002ef7	78.11011	Usage: EXTEND LUN {SIZE= [DRIVES=[,[,...]]] \| DRIVES=[,[,...]]} [NOERR] Extends the size of the currently selected LUN. SIZE= Specifies the size in megabytes to extend the LUN by. To specify the size using other units, use one of the recognized suffixes (B, KB, MB, GB, TB and PB) immediately after the size. DRIVES=[,[,...]] Specifies the indexes of the drives to use to extend the LUN. If the SIZE= parameter is not specified, the LUN is extended by the largest possible size allowed by all of the specified drives. NOERR For scripting only. When an error is encountered, DiskRAID continues to process commands as if the error did not occur. Without the NOERR parameter, an error causes DiskRAID to exit with an error code. A LUN must be selected for this operation to succeed. Examples: EXTEND LUN SIZE=5GB EXTEND LUN DRIVES=0,2 NOERR
0x40002ef9	78.11011	Usage: FLUSHCACHE CONTROLLER Flushes the cache on the currently selected controller. A controller must be selected for this operation to succeed. Example: FLUSHCACHE CONTROLLER
0x40002efb	78.11011	Usage: HELP Displays the list of commands recognized by DiskRAID. Example: HELP
0x40002eff	78.11011	Usage: INVALIDATECACHE CONTROLLER Invalidates the cache on the currently selected controller. A controller must be selected for this operation to succeed. Example: INVALIDATECACHE CONTROLLER
0x40002f01	78.11011	Usage: LIST
0x40002f03	78.11011	Usage: MAINTENANCE
0x40002f0b	78.11011	Usage: OFFLINE
0x40002f0d	78.11011	Usage: ONLINE
0x40002f0f	78.11011	Usage: RECOVER LUN Performs operations necessary to repair the currently selected LUN. A LUN must be selected for this operation to succeed. Example: RECOVER LUN
0x40002f13	78.11011	Usage: REENUMERATE {SUBSYSTEMS \| DRIVES} Re-enumerates objects of the specified type. SUBSYSTEMS Re-queries the available subsystems to discover any new subsystems that were added. A provider must be selected for this operation to succeed. DRIVES Re-inventories the drives in the currently selected subsystem. A subsystem must be selected for this operation to succeed. Example: REENUMERATE DRIVES
0x40002f15	78.11011	Usage: REFRESH PROVIDER Refreshes internal data for the currently selected provider. A provider must be selected for this operation to succeed. Example: REFRESH PROVIDER
0x40002f17	78.11011	Usage: REM [] Does nothing. Used to comment scripts. Example: REM This is a comment.
0x40002f19	78.11011	Usage: REPLACE DRIVE= Replaces the specified drive with the currently selected drive. DRIVE= Specifies the index of the drive to be replaced. This drive must be different from the currently selected drive. A drive must be selected for this operation to succeed. Example: REPLACE DRIVE=0
0x40002f1d	78.11011	Usage: RESET
0x40002f1f	78.11011	Usage: SELECT
0x40002f21	78.11011	Usage: SETFLAG DRIVE HOTSPARE={TRUE \| FALSE} Sets the specified flag to the specified value for the currently selected drive. HOTSPARE={TRUE \| FALSE} If TRUE, specifies that the drive is reserved for use only as a hot spare. A drive must be selected for this operation to succeed. Example: SETFLAG DRIVE HOTSPARE=TRUE
0x40002f22	78.11011	Usage: SHRINK LUN SIZE= [NOERR] Reduces the size of the selected LUN. SIZE= Specifies the desired amount of space in megabytes (MB) to reduce the size of the LUN by. To specify the size using other units, use one of the recognized suffixes (B, KB, MB, GB, TB and PB) immediately after the size. NOERR For scripting only. When an error is encountered, DiskRAID continues to process commands as if the error did not occur. Without the NOERR parameter, an error causes DiskRAID to exit with an error code. A LUN must be selected for this operation to succeed. Examples: SHRINK LUN SIZE=5120 SHRINK LUN SIZE=5GB SHRINK LUN SIZE=5GB NOERR
0x40002f23	78.11011	Usage: UNMASK LUN {ALL \| NONE \| [ADD] WWN=[;[;...]] \| [ADD] INITIATOR=[;[;...]]} [UNINSTALL] Makes the currently selected LUN accessible from the specified host(s). ALL Specifies that the LUN should be made accessible from all hosts that are discoverable by the VDS Hardware provider supporting the subsystem. This generally always includes the local host server, and may include other servers. NONE Specifies that the LUN should not be accessible to any host server. ADD Specifies that the given host servers must be added to the existing list of host servers that are able to access this LUN. If this parameter is not specified, the list of specified hosts replaces the existing list of hosts that this LUN is accessible from. WWN=[;[;...]] Used with PCI RAID, Fibre Channel or SAS subsystems. Specifies a list of World Wide Names of host ports that the LUN should be made accessible to. Each WWN is separated by a semicolon. For example if you specify the WWN of the Fibre Channel HBA port on Server1, the LUN becomes visible as an operating system disk at Server1. INITIATOR=[;[;...]] Used with iSCSI subsystems. Specifies a list of iSCSI host initiator names. Each iSCSI host initiator name is separated by a semicolon. Although a LUN must be selected to run this command, the command may operate on the target containing the LUN, rather than a specific LUN. The behavior of this command differs depending on the iSCSI implementation. For example, 1) Some iSCSI implementations may put all LUNs in one target. 2) Some iSCSI implementations may create one target per LUN. 3) Some iSCSI implementations may allow multiple targets, and allow the user to associate LUNs with specific targets. This implementation is used by the Microsoft iSCSI Software Target. At a minimum, this command specifies that the target associated with the LUN will allow the given initiator access to the target. For some implementations, allowing initiator access to a target means that once the initiator logs in to the target, the initiator will have access to all LUNs contained in the target. This implementation is used by the Microsoft iSCSI Software Target. For the Microsoft iSCSI Software Target, access is restricted by placing LUNs in multiple targets, and then allowing access on a per-target basis. For other implementations, the initiator may have access only to the LUN that is selected when the command is run. UNINSTALL If specified, uninstalls the disk associated with the LUN, on the local system, before the LUN is masked. Before uninstallng the disk, for each volume with extents on the disk, the file system is dismounted, the volume is offined and the volume is uninstalled. Also removes obsolete drive letters and mounted folders associated with volumes on the disk. A LUN must be selected for this operation to succeed. Examples: UNMASK LUN NONE UNMASK LUN WWN=10000000C9241FBD UNMASK LUN ADD WWN=100000009E3F0076;100000009E3F8A73 UNMASK LUN INITIATOR=iqn.2429-08.com.myinitiators.initiator-3
0x40002f25	78.11011	Usage: CHAP INITIATOR SET SECRET=[<"secret">] [TARGET=] CHAP INITIATOR REMEMBER SECRET=[<"secret">] TARGET= CHAP TARGET SET SECRET=[<"secret">] [INITIATOR=] CHAP TARGET REMEMBER SECRET=[<"secret">] INITIATOR= Sets the CHAP secret for the local initiator or currently selected target. Enter: CHAP INITIATOR /? for specific help on setting local-initiator CHAP secrets. CHAP TARGET /? for specific help on setting target CHAP secrets.
0x40002f27	78.11011	Usage: IMPORTTARGET SUBSYSTEM [SET TARGET] Displays or sets the current VSS import target for the currently selected subsystem. SET TARGET Sets the currently selected target as the VSS import target. A subsystem must be selected for this operation to succeed. If SET TARGET is specified, a target must also be selected for this operation to succeed. Examples: IMPORTTARGET SUBSYSTEM IMPORTTARGET SUBSYSTEM SET TARGET
0x40002f29	78.11011	Usage: INITIATOR Displays detailed information about the local iSCSI initiator. Example: INITIATOR
0x40002f2b	78.11011	Usage: IPSEC IPORTAL TPORTAL= IPSEC IPORTAL SET KEY=[] TPORTAL= [ [ [...]]] IPSEC IPORTAL SET TUNNEL= DESTINATION= IPSEC TPORTAL IPORTAL= IPSEC TPORTAL SET KEY=[] {INITIATOR \| IPORTAL=} [ [ [...]]] IPSEC TPORTAL SET TUNNEL= DESTINATION= IPSEC SUBSYSTEM SET GROUPKEY=[] IPSEC INITIATOR SET GROUPKEY=[] IPSEC INITIATOR SET KEY=[] TPORTAL= [ [ [...]]] IPSEC INITIATOR SET TUNNEL= DESTINATION= Sets or displays the IPSEC policy for the currently selected iSCSI initiator portal, target portal, subsystem, or local initiator. Enter: IPSEC IPORTAL /? for specific help on setting initiator portal IPSEC policy IPSEC TPORTAL /? for specific help on setting target portal IPSEC policy IPSEC SUBSYSTEM /? for specific help on setting subsystem-wide IPSEC policy IPSEC INITIATOR /? for specific help on setting local-initiator-wide IPSEC policy
0x40002f2d	78.11011	Usage: LBPOLICY SET LUN TYPE= [PATHS=-{PRIMARY \| } [,-{PRIMARY \| }[,...]]] LBPOLICY SET LUN PATHS=-{PRIMARY \| } [,-{PRIMARY \| }[,...]] Sets the load balance policy for the currently selected LUN. TYPE= Specifies the type of load balance policy. Must be one of FAILOVER, ROUNDROBIN, SUBSETROUNDROBIN, DYNLQD, WEIGHTED, LEASTBLOCKS, or VENDORSPECIFIC. PATHS=-{PRIMARY \| }[,-{PRIMARY \| }[,...]] Specifies one or more paths describing the load balance policy. Specifies the index of a path. This must refer to one of the currently selected LUN's paths. PRIMARY Specifies that the path is a primary path. Any paths not specified are implicitly set as backup. Specifies the weight of the path. A LUN must be selected for this operation to succeed. Examples: LBPOLICY SET LUN TYPE=FAILOVER PATHS=3-PRIMARY LBPOLICY SET LUN TYPE=WEIGHTED PATHS=2-45,4-10,7-30 LBPOLICY SET LUN PATHS=5-PRIMARY
0x40002f2f	78.11011	Usage: LOGIN TARGET IADAPTER= [TYPE={MANUAL \| PERSISTENT \| BOOT}] [CHAP={NONE \| ONEWAY \| MUTUAL}] [TPORTAL=] [IPORTAL=] [ [ [...]]] Logs the specified initiator adapter into the current in-focus target. IADAPTER= Specifies the index of the initiator adapter to use. TYPE={MANUAL \| PERSISTENT \| BOOT} Specifies the type of login to perform. If unspecified, a manual login will be performed. CHAP={NONE \| ONEWAY \| MUTUAL} Specifies the type of CHAP authentication to use. If unspecified, no authentication will be used. TPORTAL= Specifies a index of the target portal in the currently selected subsystem to use for the login. IPORTAL= Specifies a index of the initiator portal in the specified initiator adapter to use for the login. Specifies a flag to enable during login. Flags are identified by three-letter acronyms: IPS - Require IPSEC EMP - Enable multipath EHD - Enable header digest EDD - Enable data digest A target must be selected for this operation to succeed. Examples: LOGIN TARGET IADAPTER=1 LOGIN TARGET IADAPTER=0 TYPE=PERSISTENT CHAP=ONEWAY IPS EMP
0x40002f31	78.11011	Usage: LOGOUT TARGET IADAPTER= Logs the specified initiator adapter out of the currently selected target. IADAPTER= Specifies the index of the initiator adapter to use. A target must be selected for this operation to succeed. Example: LOGOUT TARGET IADAPTER=1
0x40002f33	78.11011	Usage: NAME
0x40002f35	78.11011	Usage: REMOVE TPGROUP TPORTAL= [NOERR] Removes the target portal from the currently selected target portal group. TPORTAL= Specifies the index of the target portal to remove. NOERR For scripting only. When an error is encountered, DiskRAID continues to process commands as if the error did not occur. Without the NOERR parameter, an error causes DiskRAID to exit with an error code. A target portal group must be selected for this operation to succeed. Example: REMOVE TPGROUP TPORTAL=1 NOERR
0x40002f37	78.11011	Usage: STANDBY HBAPORT Sets the state of paths to the currently selected HBA port to standby. An HBA port must be selected for this operation to succeed. Example: STANDBY HBAPORT
0x400030d5	78.11011	Usage: CREATE LUN {SIZE= [DRIVES=[,[,...]]] \| DRIVES=[,[,...]] \| SIZE= [POOL=] \| POOL=} [STRIPESIZE=] [BUS=] [NOERR] Creates a new LUN. Specifies the type of LUN to create. This must be one of SIMPLE, SPAN, STRIPE, MIRROR, RAID, AUTOMAGIC, RAID2, RAID3, RAID4, RAID5, RAID6, RAID01, RAID03, RAID05, RAID10, RAID15, RAID30, RAID50, RAID51, RAID53, RAID60 and RAID61. Specifying AUTOMAGIC type will create a LUN using the automagic hints currently in effect. Automagic hints are displayed and set by the AUTOMAGIC command. SIZE= Specifies the total LUN size in megabytes. To specify the size using other units, use one of the recognized suffixes (B, KB, MB, GB, TB and PB) immediately after the size. DRIVES=[,[,...]] Specifies the indexes of the drives to use to create the LUN. If the SIZE= parameter is not specified, the LUN created is the largest possible size allowed by all of the specified drives. This parameter cannot be specified along with the POOL parameter. POOL= Specifies the index of the storage pool to use to create the LUN. This parameter cannot be specified along with the DRIVES parameter. STRIPESIZE= Specifies the interleave size in megabytes for a STRIPE or RAID LUN. To specify the size using other units, use one of the recognized suffixes (B, KB, MB, GB, TB and PB) immediately after the size. BUS= Specifies the bus type of the drives to use to create the LUN. This must be one of SCSI, ATAPI, ATA, 1394, SSA, FIBRE, USB, RAID, ISCSI, SAS, SATA, SD and MMC. NOERR For scripting only. When an error is encountered, DiskRAID continues to process commands as if the error did not occur. Without the NOERR parameter, an error causes DiskRAID to exit with an error code. A subsystem must be selected for this operation to succeed. Examples: CREATE LUN SIMPLE SIZE=1GB CREATE LUN MIRROR DRIVES=1,4 CREATE LUN AUTOMAGIC SIZE=1TB NOERR
0x400030d7	78.11011	Usage: CREATE TARGET NAME=<"name"> [ISCSINAME=] [NOERR] Creates a new target. NAME=<"name"> Specifies the name to assign to the new target. This name must be less than 64 characters in length. ISCSINAME= Specifies the iSCSI name to assign to the new target. If no iSCSI name is specified the provider will attempt to generate an iSCSI name for the target. NOERR For scripting only. When an error is encountered, DiskRAID continues to process commands as if the error did not occur. Without the NOERR parameter, an error causes DiskRAID to exit with an error code. A subsystem must be selected for this operation to succeed. Examples: CREATE TARGET NAME="MyTarget" CREATE TARGET NAME="Backup" ISCSINAME=iqn.1991-05.com.mydomain:backuptarget CREATE TARGET NAME="Storage for My Computer" NOERR
0x400030d9	78.11011	Usage: CREATE TPGROUP [NOERR] Creates a new target portal group. NOERR For scripting only. When an error is encountered, DiskRAID continues to process commands as if the error did not occur. Without the NOERR parameter, an error causes DiskRAID to exit with an error code. A target must be selected for this operation to succeed. Example: CREATE TPGROUP NOERR
0x400030df	78.11011	Usage: CHAP INITIATOR SET SECRET=[<"secret">] [TARGET=] CHAP INITIATOR REMEMBER SECRET=[<"secret">] TARGET= Sets the CHAP secret for the local initiator or remembers the CHAP secret required to authenticate the initiator to the specified target. SET Specifies that the CHAP secret will be set for the local initiator. REMEMBER Specifies that the CHAP secret will be remembered by the local initiator to use to authenticate to the target specified by TARGET=. SECRET=[<"secret">] Specifies the secret to set or remember. If empty the secret will be cleared. TARGET= Specifies the index of the target in the currently selected subsystem with which to associate the secret. If specified, a subsystem must be selected for this operation to succeed. Example: CHAP INITIATOR SET SECRET="3A9cf0bb59" CHAP INITIATOR REMEMBER SECRET="my secret password" TARGET=3
0x400030e0	78.11011	Usage: CHAP TARGET SET SECRET=[<"secret">] [INITIATOR=] CHAP TARGET REMEMBER SECRET=[<"secret">] INITIATOR= Sets the CHAP secret for the currently selected target or remembers the CHAP secret required to authenticate the target to the specified initiator. SET Specifies that the CHAP secret will be set for target. REMEMBER Specifies that the CHAP secret will be remembered by the target to use to authenticate to the initiator specified by INITIATOR=. SECRET=[<"secret">] Specifies the secret to set or remember. If empty the secret will be cleared. INITIATOR= Specifies the initiator iSCSI name with which to associate the secret. A target must be selected for this operation to succeed. Example: CHAP TARGET SET SECRET="3A9cf0bb59" CHAP TARGET REMEMBER SECRET="my secret password" INITIATOR=iqn.2429-08.com.myinitiators.initiator-3
0x400030e9	78.11011	Usage: IPSEC IPORTAL TPORTAL= IPSEC IPORTAL SET KEY=[] TPORTAL= [ [ [...]]] IPSEC IPORTAL SET TUNNEL= DESTINATION= Displays or configures IPSEC information on the currently selected initiator portal. TPORTAL= Specifies the index of the associated target portal with which to display or configure the IPSEC information. If specified, a subsystem must be selected for this operation to succeed. SET Specifies that IPSEC information will be set on the initiator portal. KEY=[] Specifies the IPSEC key to set. If empty, the key will be cleared. Specifies the flags to enable. Flags are identified by three-letter acronyms: IKE - Enable IPSEC/IKE NMM - Enable IPSEC negotiating through main mode NAM - Enable IPSEC negotiating through aggressive mode PFS - Enable perfect forward secrecy TRA - Prefer transport mode TUN - Prefer tunnel mode TUNNEL= Specifies the tunnel mode address to set. DESTINATION= Specifies the destination address to associate with the tunnel mode address. An initiator portal must be selected for this operation to succeed. Example: IPSEC IPORTAL TPORTAL=3 IPSEC IPORTAL SET KEY=8dfc93a12d TPORTAL=1 IKE NMM TRA IPSEC IPORTAL SET TUNNEL=tunnel.mycorp.com DESTINATION=68.29.1.80
0x400030ea	78.11011	Usage: IPSEC TPORTAL IPORTAL= IPSEC TPORTAL SET KEY=[] {INITIATOR \| IPORTAL=} [ [ [...]]] IPSEC TPORTAL SET TUNNEL= DESTINATION= Displays or configures IPSEC information on the currently selected target portal. IPORTAL= Specifies the index of the associated initiator portal with which to display or configure the IPSEC information. If specified, an initiator adapter must be selected for this operation to succeed. SET Specifies that IPSEC information will be set on the target portal. KEY=[] Specifies the IPSEC key to set. If empty, the key will be cleared. INITIATOR Specifies that the key should be associated with all local initiator portals. Specifies the flags to enable. Flags are identified by three-letter acronyms: IKE - Enable IPSEC/IKE NMM - Enable IPSEC negotiating through main mode NAM - Enable IPSEC negotiating through aggressive mode PFS - Enable perfect forward secrecy TRA - Prefer transport mode TUN - Prefer tunnel mode TUNNEL= Specifies the tunnel mode address to set. DESTINATION= Specifies the destination address to associate with the tunnel mode address. A target portal must be selected for this operation to succeed. Example: IPSEC TPORTAL IPORTAL=1 IPSEC TPORTAL SET KEY=8dfc93a12d INITIATOR IKE NMM TUN IPSEC TPORTAL SET TUNNEL=tunnel.mycorp.com DESTINATION=68.29.1.55
0x400030eb	78.11011	Usage: IPSEC SUBSYSTEM SET GROUPKEY=[] Sets the group IPSEC key for the target portals of the currently selected subsystem. GROUPKEY=[] Specifies the group IPSEC key to set. If empty the key will be cleared. A subsystem must be selected for this operation to succeed. Example: IPSEC SUBSYSTEM SET GROUPKEY=8dfc93a12d
0x400030ec	78.11011	Usage: IPSEC INITIATOR SET GROUPKEY=[] IPSEC INITIATOR SET KEY=[] TPORTAL= [ [ [...]]] IPSEC INITIATOR SET TUNNEL= DESTINATION= Sets the IPSEC information on the local initiator and its initiator portals. GROUPKEY=[] Specifies the group IPSEC key to set. If empty the key will be cleared. KEY=[] Specifies the IPSEC key to set. If empty, the key will be cleared. TPORTAL= Specifies the index of the associated target portal with which to configure the IPSEC information. If specified, a subsystem must be selected for this operation to succeed. Specifies the flags to enable. Flags are identified by three-letter acronyms: IKE - Enable IPSEC/IKE NMM - Enable IPSEC negotiating through main mode NAM - Enable IPSEC negotiating through aggressive mode PFS - Enable perfect forward secrecy TRA - Prefer transport mode TUN - Prefer tunnel mode TUNNEL= Specifies the tunnel mode address to set. DESTINATION= Specifies the destination address to associate with the tunnel mode address. Example: IPSEC INITIATOR SET GROUPKEY=8dfc93a12d IPSEC INITIATOR SET KEY=8dfc93a12d TPORTAL=2 IKE IPSEC INITIATOR SET TUNNEL=tunnel.mycorp.com DESTINATION=68.29.1.80
0x400032c9	78.11011	Iadap ### Name --------- ------------------------------
0x400032ca	78.11011	%1!s! Iadap %2!-3lu! %3!-30.30s!
0x400032cb	78.11011	There are no initiator adapters to list.
0x400032d3	78.11011	Initiator adapter %1!d! is now the selected initiator adapter.
0x400032d4	78.11011	There is no initiator adapter selected. To select an initiator adapter, specify the Iadap ### for the initiator adapter you wish to select. Example: SELECT IADAPTER 0 To get a list of available initiator adapter, enter LIST IADAPTERS.
0x400032dd	78.11011
0x400032e6	78.11011	%1!d! Path(s):
0x4000332d	78.11011	Iptl ### Address -------- ------------------------------
0x4000332e	78.11011	%1!s! Iptl %2!-3lu! %3!-30.30s!
0x4000332f	78.11011	There are no initiator portals to list.
0x40003337	78.11011	Initiator portal %1!d! is now the selected initiator portal.
0x40003338	78.11011	There is no initiator portal selected. To select an initiator portal, specify the Iptl ### for the initiator portal you wish to select. Example: SELECT IPORTAL 0 To get a list of available initiator portal, enter LIST IPORTALS.
0x40003341	78.11011	Address : %1!s! iSCSI Port Index : %2!d!
0x4000334a	78.11011	%1!d! Path(s):
0x40003391	78.11011	Tptl ### Address Status Targets -------- ------------------------------ ---------- -------
0x40003392	78.11011	%1!s! Tptl %2!-3lu! %3!-30.30s! %4!-10.10s! %5!7d!
0x40003393	78.11011	There are no target portals to list.
0x4000339b	78.11011	Target portal %1!d! is now the selected target portal.
0x4000339c	78.11011	There is no target portal selected. To select a target portal, specify the Tptl ### for the target portal you wish to select. Example: SELECT TPORTAL 0 To get a list of available target portals, enter LIST TPORTALS.
0x400033a5	78.11011	Address : %1!s!
0x400033ae	78.11011	%1!d! Path(s):
0x400033b7	78.11011	%1!u! Associated Target Portal Group(s):
0x400033b8	78.11011	No target portal groups are associated with this target portal.
0x400033f5	78.11011	Target ### Name Chap LUNs ---------- ------------------------------ ---- ----
0x400033f6	78.11011	%1!s! Target %2!-3lu! %3!-30.30s! %4!-3.3s! %5!4d!
0x400033f7	78.11011	There are no targets to list.
0x400033ff	78.11011	Target %1!d! is now the selected target.
0x40003400	78.11011	There is no target selected. To select a target, specify the Target ### for the target you wish to select. Example: SELECT TARGET 0 To get a list of available targets, enter LIST TARGETS.
0x40003409	78.11011	iSCSI Name : %1!s!
0x40003417	78.11011	%1!u! Associated LUN(s):
0x40003418	78.11011	No LUNs are associated with this target.
0x4000341d	78.11011	%1!u! Connected Initiator(s):
0x4000341e	78.11011	No initiators are connected to this target.
0x40003459	78.11011	Tpgrp ### Target ### TPortals --------- ---------- --------
0x4000345a	78.11011	%1!s! Tpgrp %2!-3lu! Target %3!-3lu! %4!8d!
0x4000345b	78.11011	There are no target portal groups to list.
0x40003463	78.11011	Target portal group %1!d! is now the selected target portal group.
0x40003464	78.11011	There is no target portal group selected. To select a target portal group, specify the Tpgrp ### for the target portal group you wish to select. Example: SELECT TPGROUP 0 To get a list of available target portal groups, enter LIST TPGROUPS.
0x4000346d	78.11011	Tag : %1!d!
0x4000347d	78.11011	%1!u! Associated Target Portal(s):
0x4000347e	78.11011	No target portals are associated with this target portal group.
0x400034bd	78.11011	Flag Enabled ------------------------------------------------------- ----------
0x400034be	78.11011	IKE - Enable IPSEC/IKE %1!-10.10s!
0x400034bf	78.11011	NMM - Enable IPSEC negotiating through main mode %1!-10.10s!
0x400034c0	78.11011	NAM - Enable IPSEC negotiating through aggressive mode %1!-10.10s!
0x400034c1	78.11011	PFS - Enable perfect forward secrecy %1!-10.10s!
0x400034c2	78.11011	TRA - Prefer transport mode %1!-10.10s!
0x400034c3	78.11011	TUN - Prefer tunnel mode %1!-10.10s!
0x400034c4	78.11011	LUN ### Status Health Type Size Device LUN Num ------- ---------- ------------ -------- -------- ------ -------
0x400034c5	78.11011	%1!s! LUN %2!-3lu! %3!-10.10s! %4!-12.12s! %5!-8.8s! %6!5I64u! %7!-2.2s! %8!6.6s! %9!7.7s!
0x400034c6	78.11011	LUN number %1!d! is now the selected LUN.
0x400034c7	78.11011	Name : %1!s! Identifier : %2!s! LUN Number : %3!s! Status : %4!s! Health : %5!s! Size : %6!I64u! %7!-2.2s! Type : %8!s! Rebuild Priority : %9!d! Unmasked Hosts : %10!s! Caching Policy : %11!s! Stripe Size : %12!s! Flags : %13!s!
0x400034c8	78.11011	AHS - Allocate Hot Spare %1!18.18s!
0x400034c9	78.11011	UMC - Use Mirrored Cache %1!18.18s!
0x400034ca	78.11011	RCE - Read Cache Enabled %1!18.18s!
0x400034cb	78.11011	WCE - Write Cache Enabled %1!18.18s!
0x400034cc	78.11011	MSE - Media Scan Enabled %1!18.18s!
0x400034cd	78.11011	CCE - Consistency Check Enabled %1!18.18s!
0x400034ce	78.11011	BUS - Bus Type %1!18.18s!
0x400034d0	78.11011	Pool ### Name Status Health Size Free -------- -------------------- ---------- ------------ -------- --------
0x400034d1	78.11011	%1!s! Pool %2!-3lu! %3!-20.20s! %4!-10.10s! %5!-12.12s! %6!5I64u! %7!-2.2s! %8!5I64u! %9!-2.2s!
0x400034d2	78.11011	There are no storage pools to list.
0x400034d3	78.11011	Storage pool %1!d! is now the selected storage pool.
0x400034d4	78.11011	There is no storage pool selected. To select a storage pool, specify the Pool ### for the storage pool you wish to select. Example: SELECT POOL 0 To get a list of available storage pools, enter LIST POOLS.
0x400034d8	78.11011	Name : %1!s! Type : %2!s! Status : %3!s! Health : %4!s! Description : %5!s! Space consumed : %6!I64u! %7!s! Space managed : %8!I64u! %9!s! (%10!I64u! %11!s! Free)
0x400034d9	78.11011	Allocated Storage Pools -----------------------
0x400034da	78.11011	Allocated LUNs -----------------------
0x400034db	78.11011	Subsys ### LUN ### Status Health Type Size ---------- ------- ---------- ------------ -------- --------
0x400034dc	78.11011	Subsys %1!-3lu! LUN %2!-3lu! %3!-10.10s! %4!-12.12s! %5!-8.8s! %6!5I64u! %7!-2.2s!
0x400034dd	78.11011	Contributing Drives -----------------------
0x400034de	78.11011	Subsys ### Drive ### Size Free ---------- --------- -------- ------
0x400034df	78.11011	Subsys %1!-3lu! Drive %2!-3lu! %3!5I64u! %4!-2.2s! %5!s!
0x400034e0	78.11011	Pool Attributes -----------------------
0x400034e1	78.11011	Raid Type : %1!s!
0x400034e2	78.11011	Bus Type : %1!s!
0x400034e3	78.11011	Usage : %1!s!
0x400034e4	78.11011	Spin down : %1!s!
0x400034e5	78.11011	Thin provisioned : %1!s! Space provisioned : %2!I64u! %3!s!
0x400034e6	78.11011	Single point of failure : %1!s!
0x400034e7	78.11011	Maximum copies of data : %1!lu!
0x400034e8	78.11011	Minimum copies of data : %1!lu!
0x400034e9	78.11011	Default copies of data : %1!lu!
0x400034ea	78.11011	Maximum number of drives : %1!lu!
0x400034eb	78.11011	Minimum number of drives : %1!lu!
0x400034ec	78.11011	Default number of drives : %1!lu!
0x400034ed	78.11011	Stripe size : %1!I64u! %2!s!
0x400034ee	78.11011	Maximum Stripe size : %1!I64u! %2!s!
0x400034ef	78.11011	Minimum Stripe size : %1!I64u! %2!s!
0x400034f0	78.11011	Default Stripe size : %1!I64u! %2!s!
0x400034f1	78.11011	Number of members : %1!lu!
0x400034f2	78.11011	Maximum number of members : %1!lu!
0x400034f3	78.11011	Minimum number of members : %1!lu!
0x400034f4	78.11011	Default number of members : %1!lu!
0x400034f5	78.11011	There are no storage pools attributes to list.
0x400034f6	78.11011	Custom Attributes -----------------------
0x400034f7	78.11011	Attribute name : %1!s! Attribute value : %2!s!
0xc0002729	78.11011	Command returned: 0x%1!08x!
0xc000272e	78.11011	Usage: DISKRAID [/? \| [/s