i8042prt.sys
Associated Error Codes
Below lists error codes and symbolic names found for this module.
| Code | Found in | Description |
|---|---|---|
| 0x40050005 | 1011 | Some firmware configuration information was incomplete, so defaults were used. |
| 0x40050006 | 1011 | User configuration data is overriding firmware configuration data. |
| 0x4005000b | 1011 | The ring buffer that stores incoming keyboard data has overflowed (buffer size is configurable via the registry). |
| 0x4005000c | 1011 | The ring buffer that stores incoming mouse data has overflowed (buffer size is configurable via the PS/2 mouse properties in device manager). |
| 0x4005001c | 1011 | Could not successfully write the Controller Command Byte for the i8042. |
| 0x4005001d | 1011 | An unexpected ACKNOWLEDGE was received from the device. |
| 0x4005001f | 1011 | No PS/2 compatible mouse device was detected on the PS/2 mouse port (not a problem unless this type of mouse really is connected). |
| 0x40050020 | 1011 | The PS/2 keyboard device does not exist or was not detected. |
| 0x40050023 | 1011 | An unexpected RESET was detected from the mouse device. |
| 0x80050007 | 1011 | Unable to create the device map entry for %1. |
| 0x80050008 | 1011 | Unable to delete the device map entry for %1. |
| 0x8005000f | 1011 | The keyboard reset failed. |
| 0x80050010 | 1011 | The mouse reset failed. |
| 0x80050011 | 1011 | The device sent an incorrect response(s) following a keyboard reset. |
| 0x80050012 | 1011 | The device sent an incorrect response(s) following a mouse reset. |
| 0x80050013 | 1011 | Could not set the keyboard typematic rate and delay. |
| 0x80050014 | 1011 | Could not set the keyboard indicator lights. |
| 0x80050015 | 1011 | Could not tell the hardware to send keyboard scan codes in the set expected by the driver. |
| 0x80050019 | 1011 | Unable to create the symbolic link for %1. |
| 0x8005001e | 1011 | An unexpected RESEND was received from the device. |
| 0x80050021 | 1011 | The keyboard and mouse devices do not exist or were not detected. |
| 0x80050024 | 1011 | An unexpected RESET was detected from the mouse device. The wheel has been deactivated. |
| 0x80050025 | 1011 | A bogus RESET was detected from the mouse device. |
| 0x80050026 | 1011 | A wheel mouse was detected after a device reset. The wheel has been reactivated. |
| 0x80050027 | 1011 | A protocol error has occured. Resetting the mouse to known state. |
| 0xc0050001 | 1011 | Not enough memory was available to allocate internal storage needed for the device %1. |
| 0xc0050002 | 1011 | Not enough memory was available to allocate the ring buffer that holds incoming data for the PS/2 keyboard device. |
| 0xc0050003 | 1011 | The hardware locations for %1 could not be translated to something the memory management system understands. |
| 0xc0050004 | 1011 | The hardware resources for %1 are already in use by another device. |
| 0xc0050009 | 1011 | Could not connect the interrupt for the PS/2 keyboard device. |
| 0xc005000a | 1011 | The ISR has detected an internal state error in the driver for the PS/2 keyboard device. |
| 0xc005000d | 1011 | The Start I/O procedure has detected an internal error in the driver for the PS/2 keyboard device. |
| 0xc005000e | 1011 | The Initiate I/O procedure has detected an internal state error in the driver for the PS/2 keyboard device. |
| 0xc0050016 | 1011 | Could not set the mouse sample rate. |
| 0xc0050017 | 1011 | Could not set the mouse resolution. |
| 0xc0050018 | 1011 | Could not enable transmissions from the mouse. |
| 0xc005001a | 1011 | Exceeded the allowable number of retries (configurable via the registry) for the PS/2 keyboard device. |
| 0xc005001b | 1011 | The operation on the PS/2 keyboard device timed out (time out is configurable via the registry). |
| 0xc0050022 | 1011 | An error occurred while trying to determine the number of mouse buttons. |
| 0xc0050028 | 1011 | An error occurred while trying to acquire the device ID of the mouse |
| 0xc0050029 | 1011 | An error occurred while enabling the mouse to transmit information. The device has been reset in an attempt to make the device functional. |
| 0xc0050030 | 1011 | Not enough memory was available to allocate the ring buffer that holds incoming data for the PS/2 pointing device. |
| 0xc0050031 | 1011 | Could not connect the interrupt for the PS/2 pointing device. |
| 0xc0050032 | 1011 | The ISR has detected an internal state error in the driver for the PS/2 pointing device. |
| 0xc0050033 | 1011 | The Start I/O procedure has detected an internal error in the driver for the PS/2 pointing device. |
| 0xc0050034 | 1011 | The Initiate I/O procedure has detected an internal state error in the driver for the PS/2 pointing device. |
| 0xc0050035 | 1011 | Exceeded the allowable number of retries (configurable via the registry) for the PS/2 pointing device. |
| 0xc0050036 | 1011 | The operation on the PS/2 pointing device timed out (time out is configurable via the registry). |
| 0xc0050037 | 1011 | Could not attach to the PnP device stack. |
| 49 entries | ||