Windows / Modules / ping.exe

ping.exe

Associated Error Codes

Below lists error codes and symbolic names found for this module.

CodeFound inDescription
0x27108.11011Usage: ping [-t] [-a] [-n count] [-l size] [-f] [-i TTL] [-v TOS] [-r count] [-s count] [[-j host-list] | [-k host-list]] [-w timeout] [-R] [-S srcaddr] [-c compartment] [-p] [-4] [-6] target_name Options: -t Ping the specified host until stopped. To see statistics and continue - type Control-Break; To stop - type Control-C. -a Resolve addresses to hostnames. -n count Number of echo requests to send. -l size Send buffer size. -f Set Don't Fragment flag in packet (IPv4-only). -i TTL Time To Live. -v TOS Type Of Service (IPv4-only. This setting has been deprecated and has no effect on the type of service field in the IP Header). -r count Record route for count hops (IPv4-only). -s count Timestamp for count hops (IPv4-only). -j host-list Loose source route along host-list (IPv4-only). -k host-list Strict source route along host-list (IPv4-only). -w timeout Timeout in milliseconds to wait for each reply. -R Use routing header to test reverse route also (IPv6-only). Per RFC 5095 the use of this routing header has been deprecated. Some systems may drop echo requests if this header is used. -S srcaddr Source address to use. -c compartment Routing compartment identifier. -p Ping a Hyper-V Network Virtualization provider address. -4 Force using IPv4. -6 Force using IPv6.
0x271178.11011Value must be supplied for option %1.
0x271278.11011Bad value for option %1, valid range is from %2!d! to %3!u!.
0x271378.11011Value must be supplied for loose source route.
0x271478.11011Bad route specified for loose source route.
0x271578.11011Value must be supplied for loose source route.
0x271678.11011Bad route specified for loose source route.
0x271778.11011Missing option after -o.
0x271878.11011Value must be supplied for loose source route.
0x271978.11011Bad route specified for loose source route.
0x271a8.11011Bad value for option %1.
0x271b78.11011Bad option %1.
0x271c78.11011Bad parameter %1.
0x271d78.11011Ping request could not find host %1. Please check the name and try again.
0x271e78.11011IP address must be specified.
0x271f8.11011Unable to contact IP driver. %1
0x272078.11011Pinging %1 [%2]
0x27228.11011PING: transmit failed. %1
0x272378.11011Reply from %1:
0x272478.11011(sent %1!d!)
0x272578.11011- MISCOMPARE at offset %1!d! -
0x272678.11011time=%1!d!ms
0x272778.11011time<1ms
0x272878.11011TTL=%1!d!
0x272978.11011General failure.
0x272a78.11011Destination net unreachable.
0x272b78.11011Destination host unreachable.
0x272c78.11011Destination protocol unreachable.
0x272d78.11011Destination port unreachable.
0x272e78.11011No resources.
0x272f78.11011Bad option specified.
0x273078.11011Hardware error.
0x273178.11011Packet needs to be fragmented but DF set.
0x273278.11011Request timed out.
0x273378.11011General failure.
0x273478.11011Invalid source route specified.
0x273578.11011TTL expired in transit.
0x273678.11011TTL expired during reassembly.
0x273778.11011IP parameter problem.
0x273878.11011Source quench received.
0x273978.11011Specified option is too large.
0x273a78.11011Destination specified is invalid.
0x273b78.11011General failure.
0x273c78.11011bytes=%1!d!
0x273d78.11011Only one source route option may be specified.
0x273e78.11011A malformed source or record route option was received.
0x273f78.11011
0x274078.11011Route:
0x274178.11011%1
0x274278.11011->
0x274378.11011%1 :
0x274478.11011%1!u!
0x274578.11011Timestamp:
0x274678.11011An malformed timestamp option was received.
0x274778.11011Too many options have been specified.
0x274878.11011Unable to allocate required memory.
0x274978.11011
0x274a8.11011Unable to initialize Windows Sockets interface. %1
0x274b78.11011Pinging %1
0x274c78.11011%1 [%2]
0x274d78.11011%1 [%2] :
0x274e78.11011
0x274f78.11011Ping statistics for %1!s!: Packets: Sent = %2!d!, Received = %3!d!, Lost = %4!d! (%5!u!% loss),
0x275078.11011Control-Break
0x275178.11011Control-C
0x275278.11011Negotiating IP Security.
0x275378.11011Approximate round trip times in milli-seconds: Minimum = %1!d!ms, Maximum = %2!d!ms, Average = %3!d!ms
0x275478.11011%1!s! is not a valid address.
0x27558.11011The option %1 is only supported for %2.
0x27568.11011%1
0x27578.11011[%1]
0x27588.11011Unable to create socket. %1
0x275978.11011from %1!s!
0x275a78.11011with %1!d! bytes of data:
0x275b78.11011The source and destination address have different address family.
0x275c78.11011IPv4 Protocol is not installed.
0x275d8.11011Access denied. Option %1 requires administrative privileges.
0x27107Usage: ping [-t] [-a] [-n count] [-l size] [-f] [-i TTL] [-v TOS] [-r count] [-s count] [[-j host-list] | [-k host-list]] [-w timeout] [-R] [-S srcaddr] [-4] [-6] target_name Options: -t Ping the specified host until stopped. To see statistics and continue - type Control-Break; To stop - type Control-C. -a Resolve addresses to hostnames. -n count Number of echo requests to send. -l size Send buffer size. -f Set Don't Fragment flag in packet (IPv4-only). -i TTL Time To Live. -v TOS Type Of Service (IPv4-only. This setting has been deprecated and has no effect on the type of service field in the IP Header). -r count Record route for count hops (IPv4-only). -s count Timestamp for count hops (IPv4-only). -j host-list Loose source route along host-list (IPv4-only). -k host-list Strict source route along host-list (IPv4-only). -w timeout Timeout in milliseconds to wait for each reply. -R Use routing header to test reverse route also (IPv6-only). -S srcaddr Source address to use. -4 Force using IPv4. -6 Force using IPv6.
0x271a7Bad option after -o.
0x271f7Unable to contact IP driver. %1!ws!
0x27227PING: transmit failed. %1!ws!
0x274a7Unable to initialize Windows Sockets interface. %1!ws!
0x27557The option %1!s! is only supported for %2!hs!.
0x27567%1!hs!
0x27577[%1!hs!]
0x27587Unable to create socket. %1!ws!
86 entries