serial.sys
Associated Error Codes
Below lists error codes and symbolic names found for this module.
| Code | Found in | Description |
|---|---|---|
| 0x40060001 | 1011 | The kernel debugger is already using %2. |
| 0x40060002 | 1011 | While validating that %2 was really a serial port, a fifo was detected. The fifo will be used. |
| 0x40060003 | 1011 | User configuration data for parameter %2 overriding firmware configuration data. |
| 0x40060022 | 1011 | Disabling %2 as requested by the configuration data. |
| 0x80060004 | 1011 | Unable to create the symbolic link for %2. |
| 0x80060005 | 1011 | Unable to create the device map entry for %2. |
| 0x80060006 | 1011 | Unable to delete the device map entry for %2. |
| 0x8006002a | 1011 | There is a serial mouse using the same interrupt as %2. Therefore, %2 will not be started. |
| 0x8006002b | 1011 | There was a serial mouse found on %2. Therefore, %2 will be assigned to the mouse. |
| 0xc0060007 | 1011 | Another driver on the system, which did not report its resources, has already claimed the interrupt used by %2. |
| 0xc0060008 | 1011 | Not enough resources were available for the driver. |
| 0xc0060009 | 1011 | The baud clock rate configuration is not supported on device %2. |
| 0xc006000a | 1011 | The hardware locations for %2 could not be translated to something the memory management system could understand. |
| 0xc006000b | 1011 | The hardware resources for %2 are already in use by another device. |
| 0xc006000c | 1011 | No memory could be allocated in which to place new data for %2. |
| 0xc006000d | 1011 | While validating that %2 was really a serial port, the interrupt enable register contained enabled bits in a must be zero bitfield. The device is assumed not to be a serial port and will be deleted. |
| 0xc006000e | 1011 | While validating that %2 was really a serial port, the modem control register contained enabled bits in a must be zero bitfield. The device is assumed not to be a serial port and will be deleted. |
| 0xc006000f | 1011 | While validating that %2 was really a serial port, the interrupt id register contained enabled bits in a must be zero bitfield. The device is assumed not to be a serial port and will be deleted. |
| 0xc0060010 | 1011 | While validating that %2 was really a serial port, the baud rate register could not be set consistantly. The device is assumed not to be a serial port and will be deleted. |
| 0xc0060011 | 1011 | Some firmware configuration information was incomplete. |
| 0xc0060012 | 1011 | No Parameters subkey was found for user defined data. This is odd, and it also means no user configuration can be found. |
| 0xc0060013 | 1011 | Specific user configuration data is unretrievable. |
| 0xc0060014 | 1011 | On parameter %2 which indicates a multiport card, must have a port index specified greater than 0. |
| 0xc0060015 | 1011 | On parameter %2 which indicates a multiport card, the port index for the multiport card is too large. |
| 0xc0060016 | 1011 | The bus type for %2 is not recognizable. |
| 0xc0060017 | 1011 | The bus type for %2 is not available on this computer. |
| 0xc0060018 | 1011 | The bus specified for %2 does not support the specified method of interrupt. |
| 0xc0060019 | 1011 | User configuration for parameter %2 must have %3. |
| 0xc006001a | 1011 | The user specified port for %2 is way too high in physical memory. |
| 0xc006001b | 1011 | The status port for %2 is way too high in physical memory. |
| 0xc006001c | 1011 | The status port for %2 overlaps the control registers for the device. |
| 0xc006001d | 1011 | The control registers for %2 overlaps with the %3 control registers. |
| 0xc006001e | 1011 | The status register for %2 overlaps the %3 control registers. |
| 0xc006001f | 1011 | The status register for %2 overlaps with the %3 status register. |
| 0xc0060020 | 1011 | The control registers for %2 overlaps the %3 status register. |
| 0xc0060021 | 1011 | Two ports, %2 and %3, on a single multiport card can't have two different interrupts. |
| 0xc0060023 | 1011 | Parameter %2 data is unretrievable from the registry. |
| 0xc0060024 | 1011 | While validating that %2 was really a serial port, the contents of the divisor latch register was identical to the interrupt enable and the receive registers. The device is assumed not to be a serial port and will be deleted. |
| 0xc0060025 | 1011 | Could not translate the user reported I/O port for %2. |
| 0xc0060026 | 1011 | Could not get the user reported interrupt for %2 from the HAL. |
| 0xc0060027 | 1011 | Could not translate the user reported Interrupt Status Register for %2. |
| 0xc0060028 | 1011 | Could not report the discovered legacy device %2 to the IO subsystem. |
| 0xc0060029 | 1011 | Error writing to the registry. |
| 0xc006002c | 1011 | Could not report device %2 to IO subsystem due to a resource conflict. |
| 0xc006002d | 1011 | The serial driver detected a hardware failure on device %2 and will disable this device. |
| 45 entries | ||